In situ magnesiothermic reduction synthesis of a Ge@C composite for high-performance lithium-ion batterie anodes

• Ha Tran Huu,
• Ngoc Phi Nguyen,
• Vuong Hoang Ngo,
• Huy Hoang Luc,
• Minh Kha Le,
• Minh Thu Nguyen,
• My Loan Phung Le,
• Hye Rim Kim,
• In Young Kim,
• Sung Jin Kim,
• Van Man Tran and
• Vien Vo

Beilstein J. Nanotechnol. 2023, 14, 751–761, doi:10.3762/bjnano.14.62

• report an in situ magnesiothermic reduction to synthesize a composite of Ge@C as an anode material for lithium-ion batteries. The obtained electrode delivered a specific capacity of 454.2 mAh·g−1 after 200 cycles at a specific current of 1000 mA·g−1. The stable electrochemical performance and good rate

• nanoparticles and a carbon matrix using a hydrothermal route has been reported, and the enhancement in the electrochemical performance of Ge@C electrodes was demonstrated [33]. In this work, a one-pot synthesis route has been followed to prepare a Ge@C composite using an in situ magnesiothermic reduction of

• GeO2 and biomass-derived carbon as precursor. A series of experiments using other methods to combine Ge and biomass carbon was also conducted for comparison. The in situ synthesized electrode exhibits superior electrochemical performance in lithium storage. This is attributed to a better contact

Metal-organic framework-based nanomaterials as opto-electrochemical sensors for the detection of antibiotics and hormones: A review

• Akeem Adeyemi Oladipo,
• Saba Derakhshan Oskouei and
• Mustafa Gazi

Beilstein J. Nanotechnol. 2023, 14, 631–673, doi:10.3762/bjnano.14.52

• improved electrochemical performance [63][67]. In a recent study, Tang et al. [29] used an ultrasonication and reduction process to combine nanostructured Ag nanoparticles with a MOF (ZIF-67) to fabricate nanopinna-based composite electrochemical sensors for acetaminophen detection. The results showed a

• wide linear detection range with a detection limit of 0.05 μM. Due to the synergistic effects of the wide porosity and high specific surface area of the MOF and the outstanding catalytic activity and high conductivity of Ag nanoparticles, the hybridisation improved the electrochemical performance of

Evaluation of electrosynthesized reduced graphene oxide–Ni/Fe/Co-based (oxy)hydroxide catalysts towards the oxygen evolution reaction

• Karolina Cysewska,
• Marcin Łapiński,
• Marcin Zając,
• Jakub Karczewski,
• Piotr Jasiński and
• Sebastian Molin

Beilstein J. Nanotechnol. 2023, 14, 420–433, doi:10.3762/bjnano.14.34

• reduction of the GO. A reduced form of GO combined with NiFe was also obtained by others after one-step electrodeposition by cyclic voltammetry [12]. Electrochemical studies of the catalysts towards the OER The electrochemical performance of the catalysts towards the OER was studied in an aqueous solution

Structural studies and selected physical investigations of LiCoO₂ obtained by combustion synthesis

• Monika Michalska,
• Paweł Ławniczak,
• Tomasz Strachowski,
• Adam Ostrowski and
• Waldemar Bednarski

Beilstein J. Nanotechnol. 2022, 13, 1473–1482, doi:10.3762/bjnano.13.121

• improve electrical conductivity and electrochemical performance [5][6][7][9][13][14][15][16][23][24][25][26][27][28][29][30][31][32]. Nanostructured materials can reduce the specific surface current rate as well as improve stability and specific capacity [23][24][25][26][27][28][29]. LiCoO2 has been

LED-light-activated photocatalytic performance of metal-free carbon-modified hexagonal boron nitride towards degradation of methylene blue and phenol

• Nirmalendu S. Mishra and
• Pichiah Saravanan

Beilstein J. Nanotechnol. 2022, 13, 1380–1392, doi:10.3762/bjnano.13.114

• MBN-80 thus demonstrates the enhanced electrochemical performance and lower charge transfer resistance. This mainly means an enhanced electron transfer from MBN-80 for a favourable visible light photocatalysis. Additionally, the capacitance of the electrical double layer generated at the semiconductor

Nanoarchitectonics of the cathode to improve the reversibility of Li–O₂ batteries

• Hien Thi Thu Pham,
• Jonghyeok Yun,
• So Yeun Kim,
• Sang A Han,
• Jung Ho Kim,
• Jong-Won Lee and
• Min-Sik Park

Beilstein J. Nanotechnol. 2022, 13, 689–698, doi:10.3762/bjnano.13.61

• blocked, resulting in a decrease of the electrochemical performance of LOBs [9]. In addition to the pore structure of the cathode, the morphology and physicochemical properties of Li2O2 directly affect the overpotential and round-trip efficiency of LOBs during cycling [10][11]. The morphologies and

• sufficient diffusion pathways for oxygen and electrolyte in the cathode. The ratio of Zn/Co in the starting materials greatly affects the microstructure and porosity of the resulting bimetallic ZIF–carbon/CNT composites. The correlation between the microstructure and the electrochemical performance of the

• stable electrochemical performance even at a high current density of 2,000 mA·g−1, while the Zn1Co1–C/CNT and Zn1Co4–C/CNT cathodes showed significant fading in their performance. According to plots of the overpotential (η) values for various cathodes against iapp (Supporting Information File 1, Figure

A comprehensive review on electrospun nanohybrid membranes for wastewater treatment

• Senuri Kumarage,
• Imalka Munaweera and
• Nilwala Kottegoda

Beilstein J. Nanotechnol. 2022, 13, 137–159, doi:10.3762/bjnano.13.10

• predominant PEMs [13]. Zhang et al. developed nanohybrid PVDF membranes by incorporating zeolite with enhanced thermal and electrochemical performance for lithium-ion batteries [14]. ENHs have also been used as a heterogeneous catalyst in indole synthesis by Savva et al. by incorporating gold nanoparticles

The effect of cobalt on morphology, structure, and ORR activity of electrospun carbon fibre mats in aqueous alkaline environments

• Markus Gehring,
• Tobias Kutsch,
• Osmane Camara,
• Alexandre Merlen,
• Hermann Tempel,
• Hans Kungl and
• Rüdiger-A. Eichel

Beilstein J. Nanotechnol. 2021, 12, 1173–1186, doi:10.3762/bjnano.12.87

• amount of catalytically inactive pyridinic nitrogen at higher temperatures is higher compared to non-modified fibres. As for the ORR activity of the fibre mats, it was found that for fibres containing 1.0 wt % of cobalt an increasing carbonisation temperature improves the electrochemical performance only

Progress and innovation of nanostructured sulfur cathodes and metal-free anodes for room-temperature Na–S batteries

• Marina Tabuyo-Martínez,
• Bernd Wicklein and
• Pilar Aranda

Beilstein J. Nanotechnol. 2021, 12, 995–1020, doi:10.3762/bjnano.12.75

• . Consequently, the electrocatalysts accelerate the reaction kinetics, improving the electrochemical performance of Na–S batteries. Different compounds were shown to have this property such as cobalt nanoparticles [34][45][46], iron nanoclusters [47] and iron disulfide [48], gold nanodots [49], nickel sulfide

• shuttle effect is therefore diminished, which results in an improvement in cycling stability. In this way, Qiang et al. [31] reported a decay in discharge capacity of only 3% after 8000 cycles at a high current density of 4.6 A·g−1. This improvement has also been clearly shown in the electrochemical

• performance of the RT Na–S battery reported by Xia et al. [32] who used nitrogen-doped hollow carbon nanobubbles supported on porous carbon nanofibers as sulfur hosts. The nitrogen content of this carbonaceous structure is shown by a mapping image in Figure 3C. When studying the electrochemical properties of

Solution combustion synthesis of a nanometer-scale Co₃O₄ anode material for Li-ion batteries

• Monika Michalska,
• Huajun Xu,
• Qingmin Shan,
• Shiqiang Zhang,
• Yohan Dall'Agnese,
• Yu Gao,
• Amrita Jain and
• Marcin Krajewski

Beilstein J. Nanotechnol. 2021, 12, 424–431, doi:10.3762/bjnano.12.34

• been established that the electrochemical performance of Co3O4 materials is improved when they possess either small size or appropriate pore size distribution and morphologies, such as porous or hierarchical structures, or the combination of both these features [3][4]. So far, different syntheses have

• compact structure rather than a porous one (Figure 2c). The electrochemical performance of the Co3O4 powder as anode material was evaluated in a two-electrode coin cell in a voltage window from 0.01 to 3.0 V vs Li+/Li. The first to fifth charge–discharge cycle profiles measured at a current density of 100

• ranging from 50 to 5000 mA·g−1. Flowchart of a solution combustion synthesis (SCS) of Co3O4 nanomaterial. Supporting Information Table S1: Comparison of the electrochemical performance of different Co3O4 powders applied as anode materials in Li-ion batteries (1 C = 890 mA·g‒1); Figure S1: Equivalent

ZnO and MXenes as electrode materials for supercapacitor devices

• Ameen Uddin Ammar,
• Ipek Deniz Yildirim,
• Feray Bakan and
• Emre Erdem

Beilstein J. Nanotechnol. 2021, 12, 49–57, doi:10.3762/bjnano.12.4

• high power density as well as due to the potential to further increase the energy density. Supercapacitors may act as batteries in electrochemical performance tests. The choice of the materials, their morphology, dimension, and synthesis technique, as well the synergy with the other components of the

• -dimensional (1D) and 2D nanomaterials, a good electrochemical performance can be obtained [20]. Li et al. developed dodecaborate/MXene composites. Borate has strong B–B bonds and is an important photoelectric material. Due to its high optical and electrochemical activity, borate is preferred in energy storage

• ]. Dall’Agnese et al. showed how the electrochemical performance of a supercapacitor was affected by the architecture and composition of the electrode. The electrode material was made up of a composite of Ti3C2 along with CNTs. A maximum capacitance value of 85 F·g−1 was reported with high rate capability and

Self-standing heterostructured NiC_x-NiFe-NC/biochar as a highly efficient cathode for lithium–oxygen batteries

• Shengyu Jing,
• Xu Gong,
• Shan Ji,
• Linhui Jia,
• Bruno G. Pollet,
• Sheng Yan and
• Huagen Liang

Beilstein J. Nanotechnol. 2020, 11, 1809–1821, doi:10.3762/bjnano.11.163

• Kα radiation. Electrochemical measurement The electrochemical performance of the obtained products was evaluated in CR2025 coin cells with 17 holes, each with a diameter of 1.0 mm, on the cathode side. The obtained products were directly used as the binder-free air cathode, lithium foil was used as

Structure and electrochemical performance of electrospun-ordered porous carbon/graphene composite nanofibers

• Yi Wang,
• Yanhua Song,
• Chengwei Ye and
• Lan Xu

Beilstein J. Nanotechnol. 2020, 11, 1280–1290, doi:10.3762/bjnano.11.112

• were submitted to carbonization under a N2 atmosphere at 1100 °C. The influence of the ordering and porosity of CGCNFs on their electrochemical performance was studied. The results showed that by adding deionized water to the spinning solution one could increase the number of mesopores and the specific

• improvement of the current supercapacitor electrochemical performance, the capacitance and cycle stability of supercapacitors are still subjects of research interest. Electrospinning is one of the most convenient methods to synthesize nanofibers in a continuous manner. Electrospinning has many advantages over

• conductivity impedes their use in high-power-density supercapacitors. Therefore, by adding high-performance conductive materials one can enhance the electrochemical performance of carbon nanofibers. Experiments have shown that by introducing graphene into the carbon matrix, various mechanical and

Gas sorption porosimetry for the evaluation of hard carbons as anodes for Li- and Na-ion batteries

• Yuko Matsukawa,
• Fabian Linsenmann,
• Maximilian A. Plass,
• George Hasegawa,
• Katsuro Hayashi and
• Tim-Patrick Fellinger

Beilstein J. Nanotechnol. 2020, 11, 1217–1229, doi:10.3762/bjnano.11.106

• , CO2, and H2O) for the relation with the electrochemical performance of HC anodes in lithium and sodium ion battery tests. Different to the case of graphite anodes, the geometry of the particles does not allow for conclusions on capacity losses through SEI formation. The use of Kr sorption to estimate

Atomic layer deposition for efficient oxygen evolution reaction at Pt/Ir catalyst layers

• Stefanie Schlicht,
• Korcan Percin,
• Stefanie Kriescher,
• André Hofer,
• Claudia Weidlich,
• Matthias Wessling and
• Julien Bachmann

Beilstein J. Nanotechnol. 2020, 11, 952–959, doi:10.3762/bjnano.11.79

• methods [12] as well as particles of various sizes [13] and shapes [14]. However, each study is presented as a self-sufficient piece of work with limited critical comparison to the state of the art. The conditions under which electrochemical performance is quantified (electrode substrate, electrolyte

Nickel nanoparticles supported on a covalent triazine framework as electrocatalyst for oxygen evolution reaction and oxygen reduction reactions

• Secil Öztürk,
• Yu-Xuan Xiao,
• Dennis Dietrich,
• Beatriz Giesen,
• Juri Barthel,
• Jie Ying,
• Xiao-Yu Yang and
• Christoph Janiak

Beilstein J. Nanotechnol. 2020, 11, 770–781, doi:10.3762/bjnano.11.62

• Ni/CTF-1-600-22 with 22 wt % Ni showed the best performance with a half-wave potential of 0.775 V, reaching the performance closest to the benchmark Pt/C catalyst, which shows a half-wave potential of 0.890 V under the same working conditions. The high electrochemical performance of Ni/CTF-1-600-22

Soybean-derived blue photoluminescent carbon dots

• Shanshan Wang,
• Wei Sun,
• Dong-sheng Yang and
• Fuqian Yang

Beilstein J. Nanotechnol. 2020, 11, 606–619, doi:10.3762/bjnano.11.48

• producing biocompatible CDs from biomass and biowaste and manipulating their PL characteristics. It is worth mentioning that we [33] previously studied the electrochemical performance of carbon particles of micrometer size, which were synthesized from the soybean residuals via hydrothermal carbonization and

• high-temperature annealing in nitrogen. In contrast to the analysis of the electrochemical performance of large carbon particles of micrometer size [33], this work is focused on the optical characteristics of nanometer-sized CDs, which are synthesized by two different approaches. One is similar to the

Electrochemically derived functionalized graphene for bulk production of hydrogen peroxide

• Munaiah Yeddala,
• Pallavi Thakur,
• Anugraha A and
• Tharangattu N. Narayanan

Beilstein J. Nanotechnol. 2020, 11, 432–442, doi:10.3762/bjnano.11.34

• -checked with graphite rod counter electrode, too) used as a reference and counter electrodes, respectively. The electrochemical performance of the materials was analyzed using cyclic voltammetry (CV), linear sweep voltammetry (LSV), and rotating ring and disk electrode (RRDE) measurements. A BioLogic SP

• (see Figure 2a). In order to test the durability of the materials in acidic medium, chronoamperometry studies were carried out in 0.5 M H2SO4 at 0.45 V vs RHE for 3 h. The EEG samples were studied (before and after chronoamperometry) using Raman and FTIR spectroscopy along with the electrochemical

• performance in 0.1 M KOH solution, and the data is given in Figure 5. In Figure 5a, the Raman spectra of EEG before and after 3 h of chronoamperometry are shown, which show no appreciable change in either the peak position or peak intensity. This indicates that no additional defects are created during the

High-performance asymmetric supercapacitor made of NiMoO₄ nanorods@Co₃O₄ on a cellulose-based carbon aerogel

• Meixia Wang,
• Jing Zhang,
• Xibin Yi,
• Benxue Liu,
• Xinfu Zhao and
• Xiaochan Liu

Beilstein J. Nanotechnol. 2020, 11, 240–251, doi:10.3762/bjnano.11.18

• construction of an integrated hierarchical porous nanoarchitecture by combining two metal oxides is a brilliant way to greatly enhance the overall electrochemical performance owing to synergistic effects [20]. For example, Li et al. synthesized 3D hybrid Co3O4/NiMoO4 nanowire/nanosheet arrays on a carbon cloth

• shortening of the ion diffusion length and effectively buffering the volume change in the electrochemical reaction process. More importantly, the specific surface area is enlarged for such a porous structure, facilitating reactions of active substances and improving the electrochemical performance. Our

• synthesized by a simple two-step hydrothermal method. The resulting NiMoO4@Co3O4/CA electrode shows a large specific capacitance of 436.9 C/g at 0.5 A/g, and the synergy effect of the three components is of great significance for this outstanding electrochemical performance. The ASC device based on NiMoO4

Synthesis of amorphous and graphitized porous nitrogen-doped carbon spheres as oxygen reduction reaction catalysts

• Maximilian Wassner,
• Markus Eckardt,
• Andreas Reyer,
• Thomas Diemant,
• Michael S. Elsaesser,
• R. Jürgen Behm and
• Nicola Hüsing

Beilstein J. Nanotechnol. 2020, 11, 1–15, doi:10.3762/bjnano.11.1

• correlations between structural properties and electrochemical performance. In the following we will first give a detailed structural and chemical analysis of the resulting materials (section 1 in “Results and Discussion”), followed by a discussion of their performance as ORR catalyst in electrocatalytic

Design and facile synthesis of defect-rich C-MoS₂/rGO nanosheets for enhanced lithium–sulfur battery performance

• Chengxiang Tian,
• Juwei Wu,
• Zheng Ma,
• Bo Li,
• Pengcheng Li,
• Xiaotao Zu and
• Xia Xiang

Beilstein J. Nanotechnol. 2019, 10, 2251–2260, doi:10.3762/bjnano.10.217

• redox reactions but also chemically adsorb polysulfides. In addition, rGO and carbon layer can also enhance the conductivity of C-MoS2/rGO. Therefore, the C-MoS2/rGO, as an efficient sulfur host, could exhibit excellent electrochemical performance. Experimental Preparation of defect-rich C-MoS2/rGO

• -MoS2/rGO-6 suggests that C-MoS2/rGO-6 exhibits the best polysulfide adsorption capability. In order to illustrate the better electrochemical performance of the composites, three groups of samples, MoS2-S, C-MoS2/rGO-S, C-MoS2/rGO-6-S, were used as cathodes and evaluated using CR2032 coin cells. The

A novel all-fiber-based LiFePO₄/Li₄Ti₅O₁₂ battery with self-standing nanofiber membrane electrodes

• Li-li Chen,
• Hua Yang,
• Mao-xiang Jing,
• Chong Han,
• Fei Chen,
• Xin-yu Hu,
• Wei-yong Yuan,
• Shan-shan Yao and
• Xiang-qian Shen

Beilstein J. Nanotechnol. 2019, 10, 2229–2237, doi:10.3762/bjnano.10.215

• used as self-standing electrodes for lithium-ion batteries. The structure and morphology of the fibers, and the electrochemical performance of the electrodes and the full battery were characterized. The results show that the LiFePO4 and Li4Ti5O12 fiber membrane electrodes exhibit good rate and cycle

• performance. In particular, the all-fiber-based gel-state battery composed of LiFePO4 and Li4Ti5O12 fiber membrane electrodes can be charged/discharged for 800 cycles at 1C with a retention capacity of more than 100 mAh·g−1 and a coulombic efficiency close to 100%. The good electrochemical performance is

• . Researchers have found that two-dimensional (2D) or 3D free-standing electrode materials [18][19][20][21] can significantly improve the electrochemical performance while also offering light weight and superior mechanical properties [22][23]. LiFePO4 and Li4Ti5O12 have been widely developed and applied in LIBs

Ultrathin Ni_1−xCo_xS₂ nanoflakes as high energy density electrode materials for asymmetric supercapacitors

• Xiaoxiang Wang,
• Teng Wang,
• Rusen Zhou,
• Lijuan Fan,
• Shengli Zhang,
• Feng Yu,
• Tuquabo Tesfamichael,
• Liwei Su and
• Hongxia Wang

Beilstein J. Nanotechnol. 2019, 10, 2207–2216, doi:10.3762/bjnano.10.213

• Engineering, Zhejiang University of Technology, Hangzhou, China 10.3762/bjnano.10.213 Abstract Transition metal compounds such as nickel cobalt sulfides (Ni–Co–S) are promising electrode materials for energy storage devices such as supercapacitors owing to their high electrochemical performance and good

• electrical conductivity. Developing ultrathin nanostructured materials is critical to achieving high electrochemical performance, because they possess rich active sites for electrochemical reactions, shortening the transport path of ions in the electrolyte during the charge/discharge processes. This paper

• describes the synthesis of ultrathin (around 10 nm) flower-like Ni1−xCoxS2 nanoflakes by using templated NiCo oxides. The as-prepared Ni1−xCoxS2 material retained the morphology of the initial NiCo oxide material and exhibited a much improved electrochemical performance. The Ni1−xCoxS2 electrode material

Facile synthesis of carbon nanotube-supported NiO//Fe₂O₃ for all-solid-state supercapacitors

• Shengming Zhang,
• Xuhui Wang,
• Yan Li,
• Xuemei Mu,
• Yaxiong Zhang,
• Jingwei Du,
• Guo Liu,
• Xiaohui Hua,
• Yingzhuo Sheng,
• Erqing Xie and
• Zhenxing Zhang

Beilstein J. Nanotechnol. 2019, 10, 1923–1932, doi:10.3762/bjnano.10.188

• Supporting Information File 1, Table S1. Rs and Rct are calculated to be 1.125 Ω and 0.002 Ω, respectively, indicating a high conductivity of the electrode. This good conductivity will contribute a lot to the electrochemical performance of the electrode. Besides, the high slope value at low frequencies

• indicates low ion diffusion resistance of the electrode (0.8 Ω). Therefore, the EIS results confirm the good conductivity of CC-CNT@Fe2O3 3D structures, which contributes much to the superior electrochemical performance of the CC-CNT@Fe2O3 anode. Cathode material CC-CNT@NiO NiO was successively grown on the

• to C–O and Ni–O, respectively [36]. The XPS results strongly support XRD and Raman results and confirm that NiO formed on the CC-CNT substrate, suggesting the universality of this aqueous reduction method to prepare CNT-based metal oxide composite. The electrochemical performance of the CC-CNT@NiO

TiO₂/GO-coated functional separator to suppress polysulfide migration in lithium–sulfur batteries

• Ning Liu,
• Lu Wang,
• Taizhe Tan,
• Yan Zhao and
• Yongguang Zhang

Beilstein J. Nanotechnol. 2019, 10, 1726–1736, doi:10.3762/bjnano.10.168

• electrochemical performance of Li/S batteries. The interlayer can capture the polysulfides due to the presence of oxygen functional groups and formation of chemical bonds. The hierarchically porous TiO2 nanoparticles are tightly wrapped in GO sheets and facilitate the polysulfide storage and chemical absorption

• intermediate layer and plays an important role in enhancing the electrochemical performance of Li/S batteries. It has been demonstrated that the polysulfide shuttle can be effectively suppressed by modifying the separator or incorporating an interlayer at the cathode/separator interface [21][22]. For instance

• separator. These observations indicate the stable electrochemical performance and high reversibility of the Li/S batteries with the TiO2/GO-coated separator. The discharge–charge cyclic performance was assessed at 0.2 C in the voltage range of 1.5 to 3 V (vs Li/Li+). Figure 6a shows that the Li/S batteries